filler metal
英 [ˈfɪlə(r) ˈmetl]
美 [ˈfɪlər ˈmetl]
填充金属；填隙合金；焊条
双语例句
- Interactions of laser beam with filler metal.
激光束与填充金属之间的相互作用。 - Effect of alloying elements on intermediate temperature filler metal in stepped welding of 6063 aluminum alloy
合金元素对6063铝合金阶梯焊中温钎料性能的影响 - The main reasons for the lower tensile strength when welding by one side are that the filler metal can not totally enter the bottom of the weld and there are porosities at the root of weld.
对于单面焊接接头，由于填充材料难以进入焊缝内部及根部存在气孔加剧了拉伸强度较低的程度。 - However, for attaching nonpressure parts to pressure parts, the filler metal chemistry shall match the nominal chemistry of the pressure part.
但将非受压元件焊接受压元件时所用的填充金属，应与受压元件的标称化学组成相配。 - Testing and Application for Small-tube/ tube-sheet Inner Bore Filler Metal Welding
小直径管子/管板内孔填丝对接焊试验与应用硬质合金内孔焊接车刀 - Effect of gallium on microstructure and properties of Ag-Cu-Zn filler metal
镓对AgCuZn钎料组织和性能的影响 - Based on a great deal of welding procedure qualification data, the mechanical properties prediction models of welding joints were established according to base-metal composition, filler metal compo.
本文针对实际生产过程中，焊接工艺评定要做大量的工艺评定试验，提出了利用人工神经网络和遗传算法来对焊接接头力学性能预测的方法来改进焊接工艺评定。 - Wettability and microstructure of multicomponent Cu-based active filler metal on c-BN
多元铜基活性钎料对c-BN的润湿性与微观组织 - Brazed Interface Microanalysis of Carbon-fiber Reinforced Composite Material and Titanium Alloy by Brazing Filler Metal Containing Ti Element
含Ti钎料钎焊碳纤维复合材料与钛合金的界面微观分析 - High-productivity Coating of Large Components by Means of Submerged-arc Welding with a Powder Filler Metal
大型零件的高效涂层工艺&粉末填充埋弧焊 - The results indicate that the crack is related to the chemical composition of the filler metal.
试验表明，焊接裂纹与填充材料的化学成分有一定关系。 - This paper introduces the connection using the brazing technique, selects corresponding brazing filler metal and flux together with proper technology, and determines the techniques and measures.
介绍了采用钎焊的方法进行连接；选择了相应的钎料与钎剂；并确定了工艺及措施。 - Effect of Cr on Property of Stainless Steel Joint Brazed with Series Ni-P Filler Metal
Cr对Ni-P系钎料钎焊不锈钢接头性能的影响 - The key to obtain a good bond is the ability of the filler metal to wet the YSZ.
的关键，取得了良好的债券的能力湿料的氧化锆。 - However, the correct weld filler metal must be used to eliminate cracking.
然而，必须使用正确的焊料金属以减少裂纹。 - The quantity of filler metal being often much lower than with other welding processes.
低成本的焊道，与其他焊接过程相比，填充金属的数量相对比较少。 - The stainless steel wet with brazing filler metal, before brazing aluminum alloys, it is the essential thoroughly to get rid flux residua, the joints will crack once through period of time if not.
钎料润湿不锈钢后再次与铝合金施焊前，彻底干净去除钎剂残渣是十分必要的，否则日后接头会再次开裂。 - The results show that the microstructure of brazing filler metal is mostly solid solution phase.
结果表明，钎料区主要是固溶体组织； - Study on preparation and characteristic of low melting-point Aluminum base composite filler metal
低熔点铝基复合钎料的制备及其性能研究 - To join ( metals) by applying heat, sometimes with pressure and sometimes with an intermediate or filler metal having a high melting point.
焊接通过加热，有时加压或有时用媒介物或有很高熔点的填充金属来连接（金属） - The affects of alloy elements of tin and phosphorus on the brazing properties of low silver brazing filler metal
合金元素锡和磷对低银钎料钎焊性能的影响 - The main defect in vacuum brazing Joints is that the filler metal does not penetrate into the joints completely.
真空钎焊缝中主要缺陷为未钎透，并对条状未钎透和网状未钎透进行了分析。 - The results show that the Au-Ag-Si brazing filler metal series have a good wettability with Ni.
研究结果表明：Au-Ag-Si系钎料合金与Ni润湿性良好，随着钎焊温度的增加，铺展面积增加，浸润角减小； - Investigation and application for XJ-1 type zinc-base filler metal
XJ-1型锌基钎料的研究和应用 - The characteristics of zinc-base filler metal for auto-mobile radiator soldering is introduced in the paper.
介绍了适合于汽车散热器钎焊用的锌基钎料特点。 - Main technology parameters of effects on brazing stainless steel joints using nickel base filler metal have been studied.
本文研究了影响镍基钎料钎焊不锈钢接头性能的主要工艺参数。 - The present situation of brazing on brazing technology, filler metal and flux of aluminium and its alloys is described.
综述了近年来铝及铝合金钎焊在钎焊方法、钎料及钎剂三个方面的技术发展现状，分别介绍了它们各自的发展方向。 - Active brazing filler metal Ag Cu Ti and Cu Ti were chosen to braze directly cerment and stainless steel.
选用活性钎料AgCuTi或CuTi对陶瓷与不锈钢进行直接钎接。 - Ti-10% Zr alloy was resistance-brazed with Ti based filler metal by subjecting to water or gas cooling.
用钛基组合钎料对Ti－10%Zr合金进行电阻钎焊，断电后水淬或气冷处理。 - Silver filler metal with cadmium has been used in aerospace field, household appliance and so on, for its excellent processing property.
含镉银钎料以其优异的工艺性能，在航空航天和家电等领域获得了广泛应用。